现代纺织技术 ›› 2026, Vol. 34 ›› Issue (10): 107-117.DOI: 10.12477/j.att.202603015

• • 上一篇    下一篇

碳纤维纺织复合材料的圆柱壳轴压屈曲行为与损伤机理

  

  1. 1. 浙江理工大学材料科学与工程学院,浙江杭州 310018;2. 浙江省现代纺织技术创新中心,浙江绍兴 312030
  • 出版日期:2026-10-01 网络出版日期:2026-10-20
  • 基金资助:
    浙江省“尖兵”“领雁”研发攻关项目(2024SJCZX0024)

Axial compression buckling behavior and damage mechanism of cylindrical shells made of carbon fiber textile composites

  1. 1. School of Materials Science & Engineering, Zhejiang Sci-Tech University, Hangzhou 310018, China; 2. Zhejiang Provincial Innovation Center of Advance Textile Technology, Shaoxing 312030, China
  • Published:2026-10-01 Online:2026-10-20

摘要: 为研究厚径比对纺织碳纤维复合材料圆柱壳轴向压缩屈曲行为及损伤机理的影响,采用细观-宏观多尺度有限元分析与实验验证相结合的方法,构建了考虑经纬纱卷曲特征的平纹织物细观代表性体积单元(RVE)模型,并将预测得到的宏观力学参数引入不同厚径比圆柱壳宏观模型中,开展线性与非线性屈曲分析。 结果表明:RVE 模型预测的拉伸性能与实验结果误差仅为 5. 13%,且破坏形貌吻合较好,验证了模型的可靠性。 随着厚径比增大,圆柱壳刚度与轴向承载能力明显提升,平纹 4 层圆柱壳临界屈曲载荷达到195. 24 kN。 平纹织物卷曲引起的细观应力集中与圆柱壳表层宏观应力集中叠加,是不同厚径比圆柱壳屈曲 的共同损伤诱因,均表现为分叉点处最外层首先发生微小纤维压缩损伤并诱发屈曲。 厚径比主要影响损伤累积程度,而不改变初始损伤的类型、位置及触发机制。 研究结果揭示了厚径比对平纹复合材料圆柱壳轴压屈曲性能及损伤演化的调控规律,可为结构优化设计与参数匹配提供理论参考。

关键词: 碳纤维平纹复合材料, 轴压屈曲, 有限元分析, 细观尺度, 厚径比

Abstract: Carbon fiber reinforced polymer (CFRP) composites have been widely used in various fields owing to their outstanding specific strength, specific stiffness, corrosion resistance, and lightweight characteristics, especially in scenarios subjected to high axial loads such as rocket casings and large structural supports. The thickness-to-diameter ratio is a critical factor affecting buckling. Compared with unidirectional CFRP composites, plain-weave CFRP composites exhibit more complex axial compression buckling behaviors that are difficult to analyze accurately due to their intricate interlaced structure of warp and weft yarns. Therefore, it is particularly important to investigate the buckling and post-buckling behaviors of plain-weave CFRP cylindrical shells under axial compression, clarify the influence of the thickness-to-diameter ratio on their buckling behaviors, and reveal the damage mechanisms under axial compressive buckling. In this paper, a meso-macro multi-scale finite element analysis combined with experimental verification is adopted. First, a mesoscopic representative volume element (RVE) model of plain-weave fabrics considering the crimped structure of warp and weft yarns is established to predict the macroscopic mechanical properties of the composite. These properties are then introduced into macroscopic finite element models of plain-weave CFRP cylindrical shells with different thickness-to-diameter ratios, and systematic linear and nonlinear buckling analyses are performed. The thickness-to-diameter ratio-dependent damage evolution mechanism is revealed, focusing on the buckling bifurcation point. The results show that the error between the tensile properties predicted by the proposed RVE model and the experimental data is only 5.13%, and the failure morphology is highly consistent with experimental observations, demonstrating excellent prediction accuracy of the model. The thickness-to-diameter ratio exerts a significant regulatory effect on the buckling mechanical properties of plain-weave CFRP cylindrical shells. With an increase in the thickness-to-diameter ratio, the stiffness and axial load-bearing capacity of the cylindrical shells increase exponentially, and the critical buckling load of a 4-layer plain-weave cylindrical shell can reach 195.24 kN. The superposition effect between mesoscopic local stress concentration induced by the crimped structure of plain-weave fabrics and macroscopic surface stress concentration of thin-walled shells under axial compression constitutes the common damage trigger for buckling of cylindrical shells with different thickness-to-diameter ratios. Both lead to slight compressive damage accumulation in fibers at the bifurcation point and subsequently induce buckling, with damage concentrated in the outermost layer. The thickness-to-diameter ratio only changes the quantitative degree of damage accumulation without altering the type, location, and triggering mechanism of initial damage. As the thickness-to-diameter ratio increases, the fiber compressive damage accumulation at the bifurcation point rises from 0.66% to 2.60%, yet never reaches the failure threshold and does not change the core rule that the outermost layer sustains damage first. Accordingly, this paper clarifies the correlation between the performance regulation law of the thickness-to-diameter ratio on axial compressive buckling and the damage mechanism of plain-weave CFRP cylindrical shells, providing key theoretical basis and data support for the structural optimization design and thickness-to-diameter ratio parameter matching of such components under axial compressive buckling.

Key words: carbon fiber, plain weave composite, axial compression, buckling, finite element analysis, mesoscale, thickness-to-diameter ratio

中图分类号: