现代纺织技术 ›› 2026, Vol. 34 ›› Issue (10): 38-47.DOI: 10.12477/j.att.202603060

• • 上一篇    下一篇

基于悬臂梁模型的织物弯曲性可视化测试新方法

  

  1. 1. 绍兴理工学院纺织服装与设计学院,浙江绍兴 312000;2. 浙江理工大学服装学院,浙江杭州 310018
  • 出版日期:2026-10-01 网络出版日期:2026-10-20
  • 基金资助:
    浙江省自然科学基金项目(LMS26E050016);国家自然科学基金项目(51405446)

A new method for visual testing of fabric bending properties based on cantilever beam model

  1. 1. School of Textile, Apparel and Art Design, Shaoxing Institute of Technology, Shaoxing 312000, China; 2. School of Fashion Design & Engineering, Zhejiang Sci-Tech University, Hangzhou 310018, China
  • Published:2026-10-01 Online:2026-10-20

摘要: 针对传统斜面法测试织物弯曲性能效率低、结果非可视化的问题,提出一种基于悬臂梁模型的织物弯曲性快速可视化测试方法。 构建测试装置,选取 24 种组织结构与弯曲性能各异的机织物,同步测量伸出长度、下垂高度、投影面积及弯曲系数 4 项几何指标;基于 Bernoulli-Euler 梁理论建立抗弯刚度与几何量的显式关系,并引入 Bisshopp 椭圆积分进行大变形非线性修正。 结果表明:4 项几何指标与传统斜面法所得弯曲长度、抗弯刚度均呈显著相关(P<0. 01),其中伸出长度与弯曲长度的 Pearson 相关系数在经向达 0. 877、纬向达 0. 926。 经 Bisshopp 修正后,抗弯刚度计算误差由最大 180%降至±5%以内,实现了织物弯曲形态与力学刚度的同步反演,验证了几何非线性修正的必要性。 该方法具有试样裁剪简便、测试参数可调、结果直观可视等优势。

关键词: 织物弯曲性, 弯曲长度, 可视化, 悬臂梁模型, 测试方法

Abstract: The bending properties determine fabrics' drape, garment shape, and comfort. However, the current cantilever method requires multiple samples, cutting, and repeated testing, which is time-consuming and produces inconclusive results. The research aims to develop a new method that can simultaneously obtain multiple sets of data in one test and visually display the bending differences of the fabrics and samples in various directions. Twenty-four woven fabrics with varying structures, fiber compositions, and bending properties were used as test subjects. A simple device consisting of an adjustable displacement platform, a CCD camera, and a scale was constructed. Four new parameters, namely protruding length L, falling height H, projected area A, and bending index I, were measured. The bending length C and bending stiffness B were also measured using the cantilever method for comparison. Pearson correlation and regression fitting were used to verify the correspondence between the new parameters and traditional parameters. Finally, based on the cantilever beam small-deformation model, the explicit relationship between the bending stiffness and geometric quantities was derived, and the Bisshopp elliptic integral correction was introduced to construct a stiffness inversion process under large-deformation conditions. The results show that the four new parameters L, H, A, and I were all significantly correlated with bending length C and bending stiffness B at the 0.01 or 0.05 level. The R values of L and C were ≥0.877 (0°) and 0.926 (90°), and H was quadratically negatively correlated (R² = 0.795) with bending length C. Regression models were established: C = 6.550L + 11.855 (R² = 0.815); C = -5.285H² + 35.079H - 27.433 (R² = 0.795); C and I were polynomially related. Besides, stiffer fabrics had larger projection and smaller falling height, while the opposite was true for soft fabrics. The theoretical fabric-bending stiffness values obtained from the small-deflection model differed markedly from the experimental data. After applying the Bisshopp elliptic-integral correction, the discrepancy was sharply reduced, with most errors falling within ±5% of the measured values. The single-test, multi-dimensional visualization method proposed in this article has good feasibility due to its simple device, low cost, adjustable parameters, and intuitive results. Besides, the stiffness-inversion workflow valid for large deflections established in this paper can enable an integrated bending morphology and mechanical rigidity identification as well as unify full-field visualization with quantitative stiffness determination. The approach can provide a theoretical framework for the rapid visual and quantitative evaluation of fabric-bending performance.

Key words: fabric bending, bending length, visualization, cantilever beam model, test method

中图分类号: