涤纶工业丝熔融纺丝过程的数值模拟

doi:10.19398/j.att.202201058

现代纺织技术 ›› 2022, Vol. 30 ›› Issue (5): 52-59.DOI: 10.19398/j.att.202201058

• 特约专栏:图像处理与数值模拟 • 上一篇下一篇

涤纶工业丝熔融纺丝过程的数值模拟

张伟, 成文凯, 张先明

浙江理工大学,a.材料科学与工程学院;b.纺织纤维材料与加工技术国家地方联合工程实验室,杭州 310018

收稿日期:2022-01-29 出版日期:2022-09-10 网络出版日期:2022-09-19
通讯作者:张先明,E-mail:zhangxm@zstu.edu.cn
作者简介:张伟(1998-),男,山西吕梁人,硕士研究生,主要从事新纤维材料及功能性纤维材料方面的研究。
基金资助:
浙江省重点研发计划项目(2020C01143,2021C01020)

Numerical simulation of melt spinning process of polyester industrial yarn

ZHANG Wei, CHENG Wenkai, ZHANG Xianming

a. School of Materials Science and Engineering,b. National & Local United Engineering Laboratory on Textile Fiber Materials and Processing Technology, Zhejiang Sci-Tech University, Hangzhou 310018, China

Received:2022-01-29 Published:2022-09-10 Online:2022-09-19

摘要/Abstract

摘要： 为了研究涤纶工业丝熔融纺丝过程熔体流动规律,根据企业用喷丝孔建立模型,运用三维有限元(Finite element method, FEM)数值模拟方法对涤纶工业丝熔融纺丝的过程进行了数值模拟,对比分析了喷丝孔收敛角、口模长径比以及喷丝孔入口流量对挤出过程温度场、速度场、剪切速率场以及压力场分布的影响。结果表明:温度场对喷丝孔结构变化不敏感,受入口流量影响较大;收敛角的增大会使熔体在收敛段速度增长趋势变大;长径比太大会使得熔体受口模段剪切作用增强,不利于速度均匀分布;入口流量大小对熔体流动状态影响较大。收敛角为73 °,长径比为3的喷丝孔结构最有利于速度的均匀分布。

关键词: 聚对苯二甲酸乙二醇酯, 涤纶工业丝, 熔融纺丝, 喷丝孔, 数值模拟

Abstract: In order to investigate the melt flow law of polyester industrial yarn during melt spinning, a model was built according to spinneret orifices used by enterprises and a numerical simulation of melt spinning process of polyester industrial yarn was carried out by adopting three-dimensional finite element method (FEM). The effects of the convergence angle, the aspect ratio and the distribution of inlet flow of the spinneret orifice on the temperature field, velocity field, shear rate and pressure field were compared and analyzed. The results show that the temperature field is insensitive to changes of spinneret orifice structure and is greatly affected by the inlet flow rate. When the convergence angle increases, the growth rate of velocity in transition zone increases. If the aspect ratio is too big, the shearing effect of the melt is strengthened by the die section, which is not conducive to the uniform distribution of velocity. The inlet flow rate has great influence on the melt flow state. Besides, it is the most conducive to the uniform distribution of weloaty when the spinneret orifice has an convergence angle of 73 ° and an aspect ratio of three.

Key words: polyethylene terephthalate, polyester industrial yarn, melt spinning, spinneret orifice, numerical simulation

中图分类号:

TQ342⁺.2

张伟, 成文凯, 张先明. 涤纶工业丝熔融纺丝过程的数值模拟[J]. 现代纺织技术, 2022, 30(5): 52-59.

ZHANG Wei, CHENG Wenkai, ZHANG Xianming. Numerical simulation of melt spinning process of polyester industrial yarn[J]. Advanced Textile Technology, 2022, 30(5): 52-59.

参考文献

[1] 姚军义,王玉合,吴旭华,等.国内涤纶工业丝发展现状[J].合成技术及应用,2017,32(2):26-30.
YAO Junyi, WANG Yuhe, WU Xuhua, et al. Development status of polyester industry filament in China[J]. Synthesis Technology and Application, 2017, 32(2):26-30.
[2] 王华平,吉鹏,王朝生.聚酯纤维熔体直纺仿真模型与工程化[J].高分子通报,2013(10):36-49.
WANG Huaping, JI Peng, WANG Chaosheng. The simulation model and engineering of the melt direct spinning about the polyester fiber[J]. Polymer Bulletin, 2013(10):36-49.
[3] 李永超,高雪芹,杨其,等.橡胶轮胎部件挤出过程数值模拟分析[J].高分子材料科学与工程,2016,32(3):108-112.
LI Yongchao, GAO Xueqin, YANG Qi, et al. Numerical simulation analysis of the extrusion of tire rubber part[J]. Polymer Materials Science & Engineering, 2016, 32(3): 108-112.
[4] 吴金亮,王铁军,孙福,等.细旦多孔聚酯预取向丝Barmag环吹纺丝组件的设计[J].现代纺织技术,2021,29(6):49-54.
WU Jinliang, WANG Tiejun, SUN Fu, et al. Design of barmag ring blowing spinning assembly of fine denier porous polyester pre-oriented yarn[J]. Advanced Textile Technology, 2021, 29(6): 49-54.
[5] 肖建华,柳和生,黄兴元,等.聚合物在等温圆管口模中流动的数值模拟[J].高分子材料科学与工程,2008,24(10):21-24.
XIAO Jianhua, LIU Hesheng, HUANG Xingyuan, et al. Numerical simulation of two dimention isothermal circle die flow of polymer[J]. Polymer Materials Science & Engineering, 2008, 24(10):21-24.
[6] XUE S C, BARTON G W, FLEMING S, et al. Analysis of capillary instability in metamaterials fabrication using fiber drawing technology[J]. Journal of Lightwave Technology, 2017, 35(11): 2167-2174.
[7] XUE S C, BARTON G W, FLEMING S, et al. Heat transfer modeling of the capillary fiber drawing process[J]. Journal of Heat Transfer, 2017, 139(7): 072001.
[8] KARUPPASAMY S, KRISHNAN S, KARUNANITHI B. Assessment of the flow behavior of power-law fluids in spinnerets[J]. Chemical Engineering Research and Design, 2021, 176: 134-145.
[9] QIN Y, SCHUBERT D W. Simple model to predict the effect of take-up pressure on fibre diameter of PET melt spinning[J]. Polymer, 2019, 181: 121769.
[10] JASION G T, HAYES J R, WHEELER N V, et al. Fabrication of tubular anti-resonant hollow core fibers: Modelling, draw dynamics and process optimization[J]. Optics Express, 2019, 27(15): 20567-20582.
[11] WIDJOJO N, CHUNG T S, ARIFIN D Y, et al. Elimination of die swell and instability in hollow fiber spinning process of hyperbranched polyethersulfone (HPES) via novel spinneret designs and precise spinning conditions[J]. Chemical Engineering Journal, 2010, 163(1-2): 143-153.
[12] 王华平,杨崇倡,余晓蔚,等.传热系数对中空纤维周向和径向温度梯度分布的影响[J].合成纤维工业,2001,24(3):9-13.
WANG Huaping, YANG Chongchang, YU Xiaowei, et al. The effect of heat transfer coefficient on the radial and circle temperature gradient distribution for hollow fiber[J]. China Synthetic Fiber Industry, 2001, 24(3): 9-13.

涤纶工业丝熔融纺丝过程的数值模拟

Numerical simulation of melt spinning process of polyester industrial yarn

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 10

编辑推荐

Metrics

[1]	诸文旎, 刘倩倩, JAMSHAID Hafsa, 李莉, 祝国成. 黏性颗粒在聚偏氟乙烯纤维膜内部沉积特性数值模拟[J]. 现代纺织技术, 2022, 30(5): 42-51.
[2]	邱海飞. 自排风式转杯纺纱通道内部气流场数值模拟[J]. 现代纺织技术, 2022, 30(3): 108-116.
[3]	周梓豪, 吴丽莉, 陈廷. 气相沉积法制备碳纳米管纤维反应器气体流场模拟[J]. 现代纺织技术, 2022, 30(2): 99-105.
[4]	刘宏霞, 徐佳雯, 陈廷. 气相沉积法反应器内碳纳米管纤维运动模拟[J]. 现代纺织技术, 2022, 30(2): 106-112.
[5]	谢胜，应英，方海素，申屠宝卿. 熔喷气流场与纤维运动及纤维直径的数学计算[J]. 现代纺织技术, 2019, 0(05): 15-20.
[6]	林启松，张顺花，汪凯. 架状硅酸盐粉末改性聚酯纤维的制备及性能研究[J]. 现代纺织技术, 2018, 0(05): 1-4.
[7]	徐晔，韩冬桂，刘芳，燕怒. 基于CFD的细纱机吸棉笛管流场分析与改进优化[J]. 现代纺织技术, 2018, 0(04): 83-87.
[8]	王瑞，孙冲，董余兵. 聚己内酯纤维制备的研究进展[J]. 现代纺织技术, 2017, 0(03): 17-22.
[9]	邹鹏达，陈洪立，李晓明，金玉珍. 流场状态对转杯纺纱接头行为影响的研究[J]. 现代纺织技术, 2014, 0(03): 1-4.
[10]	刘承文，金玉珍，胡旭东,汪旺. 喷气织机辅喷嘴气流场数值模拟及特性分析[J]. 现代纺织技术, 2011, 0(04): 1-5.